Electrician in Surrey, BC

Panel and service upgrades, EV chargers, heat pump circuits, knob-and-tube and aluminum wiring, suite and laneway wiring, and repairs across Cloverdale, Fleetwood, Newton and Guildford in Surrey. One licensed electrical contractor, who looks at the panel before quoting, pulls the permit and coordinates the BC Hydro side.

Licensed electrical contractor (Technical Safety BC)Electrical permit on every job that needs oneWritten quote after an in-person lookBC Hydro service work coordinated
Electrician installing a subpanel for a basement suite in a two-storey house in Newton, Surrey, BC

This line covers the north and centre of Surrey, Cloverdale, Fleetwood, Newton and Guildford, and not South Surrey or White Rock. It is a city of basement suites. Many Newton and Fleetwood houses were built or finished with a suite downstairs, some with two, all running from a single panel that was sized for one family. Guildford's 1960s and 1970s houses bring aluminum branch wiring and original 100-amp services. Cloverdale mixes older houses near the historic town centre with newer streets toward Clayton, where EV chargers and finished basements are the norm. Add heat pumps and air conditioning arriving in houses that never had them, and panel capacity is the question behind most Surrey electrical calls. One licensed electrical contractor takes these calls, quotes after seeing the panel, and handles the permit and BC Hydro.

Local Knowledge

Electrical Work in Surrey: Panels, Permits and Old Wiring

Panel capacity is the Surrey question. A house with an upstairs household and one or two suites below can have three kitchens, three sets of laundry and electric heat on a service that was designed for one. Breakers trip, panels run out of spaces, and adding a heat pump or an EV charger stops being simple. The answer starts with a load calculation of what the house actually uses. From there it might be a service upgrade to 200 amps, load management for a charger, or moving suite heating to a more efficient system so there is room for everything else.

Knob-and-tube, aluminum and the insurance question. Two kinds of older wiring come up again and again in Lower Mainland houses. Knob-and-tube, the original cloth-insulated wiring on porcelain knobs, is found in houses built before about 1950; it has no ground, it was never meant to be buried in insulation, and decades of splices often hang off it. Aluminum branch wiring was used in some houses built from the mid-1960s to the late 1970s; the wire itself is not the problem so much as its connections, which loosen and heat up at receptacles, switches and breakers if they were not made with rated devices. Many insurers ask about both at renewal or when a house is sold. Neither always means a full rewire, but both need a proper assessment and a written plan.

Permits, Technical Safety BC and who can do the work. In BC, electrical contractors are licensed through Technical Safety BC, and most electrical work beyond like-for-like replacement needs a permit and an inspection. Depending on the municipality, the permit comes from Technical Safety BC or from the city's own permit office; the contractor knows which applies at your address and applies for it. A permit protects you when you sell, when you claim on insurance and when a future electrician opens the panel. A quote that says the permit is optional, or a contractor who asks you to take out the permit in your own name, is a reason to look elsewhere.

BC Hydro and service upgrades. Electricity in Surrey comes from BC Hydro. BC Hydro supplies the service to the connection point and owns the meter; the meter base, the mast or conduit and everything inside belong to the house. For a service upgrade, the contractor takes out the electrical permit and requests the disconnect and reconnect, and BC Hydro schedules its own crew. Moving a meter, converting an overhead service to underground, or adding a separate service for a laneway or garden home goes through BC Hydro's own design process and charges, so it is raised at the quote, not discovered on the day.

Heat pumps, EV chargers and the 100-amp panel. Heat pumps, Level 2 EV chargers, induction ranges and suites all add load, and many houses here still run on a 100-amp service. Before anyone sells you a panel upgrade, a load calculation to the Canadian Electrical Code as adopted in BC shows what the service can actually carry. Sometimes the answer is a new 200-amp service; sometimes a load management device lets an EV charger share capacity without one. Heat pump rebates are listed by CleanBC Better Homes; programs change, so confirm there before counting on any amount.

Suites wired without permits. Many Surrey suites were built or rewired without permits. That matters when you sell, refinance or claim on insurance, and when a tenant's safety is involved. Bringing a suite up to code starts with an assessment of what is there: the circuits, the panel, smoke and carbon monoxide alarm interconnection, and the service capacity. The contractor then quotes the work needed and takes out the permit, so the suite is on record properly.

Where We Work

Serving Surrey & Surrounding Areas

Electrical contractor licensing and electrical permits are administered by Technical Safety BC, except where a municipality issues its own permits. Electricity in Surrey is supplied by BC Hydro. Heat pump and home energy rebates are listed by CleanBC Better Homes. WorkSafeBC requires a hazardous materials survey before renovation work on buildings built before 1990. Permit questions for your address go to City of Surrey.

Questions

Frequently Asked Questions

Do I need a permit for electrical work in Surrey?

For most work beyond replacing a fixture, receptacle or switch like for like, yes: new circuits, panel and service upgrades, EV chargers, hot tubs, suites and renovations. The contractor applies for it and arranges the inspection.

How do I know if I need a panel upgrade?

A load calculation tells you, not the age of the panel alone. Common signs are a 60- or 100-amp service with no spare spaces, breakers that trip under normal use, a fuse panel, or plans for a heat pump, EV charger or suite.

Does knob-and-tube have to be removed?

Not always all at once, but it should be assessed, and insurers often require a plan. Live knob-and-tube that has been buried in insulation or spliced into newer circuits is usually the first part to go.

Can I put an EV charger on my existing panel?

Often, yes, with a load calculation and sometimes a load management device. If the panel is full or the service is small, the contractor shows you the options and their costs side by side.

How much does an electrician cost in Surrey?

It depends on the job. Planning ranges are on the cost page. Every job is quoted in writing after the electrician has seen the panel and the work.

Do you work in condos and townhouses?

Yes. Work inside your unit is usually yours to arrange; anything on common property, including most parkade EV chargers, needs strata approval first, and the contractor can provide what the strata asks for.

Is this an electrical company?

This is a booking line for one licensed electrical contractor working across Cloverdale, Fleetwood, Newton and Guildford in Surrey. Your request goes to that contractor, not to a list or a call centre.

Ready to Get Started?

Call 778-900-8916 or send the form for a written quote for electrical work in Surrey.

By submitting this form, you agree to be contacted by phone, text, or email about your request. You can opt out at any time. Your details go only to the one local electrician who handles your job — nobody else.

Call Now: 778-900-8916